AUTONET TV

Giving CV Joints the Boot! (CV Joint and Boot Replacement)

Ever wonder how your vehicle’s transmission is connected to your wheels? After all, when you hit a pothole or some other uneven part of a road’s surface, there has to be something that can maintain the connection between the transmission and the wheel yet keep everything moving at the same speed. 

That very cool device is called a CV joint, a kind of driveshaft running to each wheel.  The CV stands for constant velocity because it keeps the drive wheels moving at a constant speed (velocity).  They’re used mostly on front-wheel drive vehicles but also in rear-wheel and all-wheel drive vehicles.

The joints move up and down and adjust to bumpy surfaces.  Plus, they are covered in a rubber boot which protects them from road debris and also holds lubrication in.  There’s a CV joint and boot on the transmission side and one on the wheel side.  Unfortunately, the spot that usually fails first is that rubber protective cover (the boot).  After a lot of wear, tear, bumps, road hazards, heat, and you name it, the rubber rips and the lubrication leaks out.  At that point, it must be replaced. 

Here are signs to tell if your CV joint is bad.

• Your vehicle is pulling to one side as a wheel loses power or you feel a vibration while driving.
• You see grease on the inside or edge of your tires.  
• Your front tires won’t point in the same direction.
• You hear grinding or clicking when you turn.

Sometimes if a broken boot early is caught early, a technician can pack in new grease and replace just the boot.  But if the lubrication has leaked out and the joint is already wearing badly, the CV and boot both have to be replaced.  Give your vehicle the boot (as in a new boot) and CV joint, and you’ll be back on the road to your next destination.

Lakeside Certified Auto
38525 Lakeshore Blvd
Willoughby, OH 44094
(440) 946-0076
http://www.lakesidecertifiedauto.com

Keeping Your Cool (Water Pump Replacement)

No matter what the temperature is outside, it's important for your vehicle's engine to remain cool, calm, and collected.  Well, cool, anyway. If your vehicle has a gasoline engine, it's powered by a bunch of explosions involving spark plugs, pistons, gasoline, and air.  And the by-product of all those things working together? HEAT.

There's a whole cooling system to keep everything at a tolerable temperature for your engine's parts, and a key part of that is the water pump.  Technically, it's pumping more than water. It should actually be called the "coolant" pump since the liquid that circulates through the system is a mixture of water and coolant. 

Basically, the water pump keeps this coolant moving through your engine, where it picks up the engine heat, and then is pumped into the radiator where it gets rid of that heat.  When a water pump fails, the engine heat can build up.  When you get a warning light on the dash (either a gauge or a light) that shows the temperature is too high, it could mean a bad water pump. 

They can fail for many reasons. They have bearings in them that wear out, as does the seal between the pump and the engine. They're often driven by a belt or chain that can go bad.  Corrosion can spell the end of a water pump, too. 

If a technician determines your water pump has failed, it's time to replace it. In addition, other components of the cooling system will be inspected.  The best way to avoid a water pump failure is regular maintenance of your cooling system which includes regular draining and flushing of the coolant. 

Just like it's important for you to keep your cool, the same goes for your vehicle's engine.

Lakeside Certified Auto
38525 Lakeshore Blvd
Willoughby, OH 44094
(440) 946-0076
http://www.lakesidecertifiedauto.com

In That Case? (Transfer Case Exchange)

Ever wonder how all-wheel-drive or 4-wheel-drive vehicles get the power from the engine to the front and rear wheels? The magic happens in what's called a transfer case.  In some all-wheel-drive vehicles, it's sometime called a power take-off unit, or PTU.

Inside the transfer case is a set of gears.  And to keep those gears meshing smoothly, they have to be lubricated and kept cool.  What does that is called transfer case fluid. Depending on your vehicle's type of transfer case, it is filled with either an automatic transmission fluid, a gear oil that's a bit thicker or transfer case fluid designed to be use for your transfer case.

As happens with all lubricating fluids, the transfer case fluid has things in it that break down the older they get.  They have corrosion inhibitors, detergents and anti-foaming agents that keep the lubricant from getting air bubbles in it. Transfer cases don't have filters in them to clean out impurities.

If you don't have your transfer case fluid exchanged for fresh, you risk damage to the case, and that can run into thousands of dollars.  So the wise driver makes sure the fluid is changed according to the manufacturer's recommendations.  For many vehicles, that is every 30,000 mi/50,000 km, but some require it more frequently.   Your vehicle service facility can advise you on what your vehicle's optimal interval is.

During the fluid exchange, any metal filings that may have come off are cleaned off of the drain and fill plugs that are usually magnetized to catch the stray metal pieces.

If you hear grinding noises coming from under your vehicle or if it is having trouble shifting gears or going in and out of 4-wheel-drive, those could be signs your transfer case needs service. In that case, have our technicians check it out.  The best plan of action?  Keep your transfer case fluid maintained and it should keep you heading down the road for years to come.

Lakeside Certified Auto
38525 Lakeshore Blvd
Willoughby, OH 44094
(440) 946-0076
http://www.lakesidecertifiedauto.com

It's Brake Time (Brake Calipers)

Race car drivers have demonstrated the advantages of disc brakes, so most modern vehicles use them.  Sometimes just the front wheels have disc brakes, but many vehicles now have them all the way around. 

A major component of the disc brake is called a caliper.  It works by squeezing brake pads against the disc or rotor, kind of like a bicycle hand brake.  The brake pads themselves are what contact the rotor, causing friction to build and the wheel to slow down, but it's the calipers that apply the pressure to the pads.

Caliper design has evolved over the years, and there are two common types.  One is called a floating caliper.  It has one or two pistons on one side of the disc. When you push down the brake pedal, the piston or pistons in your caliper put pressure on that one side.  A mechanism connected on the other side of the disc applies pressure as well, squeezing your disc so the vehicle stops.  Floating calipers are less expensive since they have fewer parts.

The other type is called a fixed caliper.  They use pistons on both sides of the disc, sometimes several.  They are often used in more high-performance or heavy-duty vehicles.

Calipers can have rubber seals to keep out dirt, debris and moisture, but when that rubber wears out, sometimes the calipers can get contaminated.  They can stick or start leaking; they can even rust.  Then your caliper can get stuck applying that "squeeze" when you are not pressing on the brake pedal.  Or they can get stuck in the other position, not applying stopping power when you press the pedal.

When this happens, it's not unusual to feel your vehicle pull to one side when you brake.  You might notice a burning smell from the constant friction if the caliper is stuck on, plus you may feel the heat from the wheel after you park and get out of your vehicle.  Sometimes you'll hear a high-pitched sound or clunk if your calipers are binding up. 

That's your cue to have them checked out at your vehicle service center.  If your calipers aren't working correctly, it can be a safety hazard.  Sticking calipers can affect your ability to steer and stop; this is the kind of "brake time" you need so you can get them back on track and working properly.

Lakeside Certified Auto
38525 Lakeshore Blvd
Willoughby, OH 44094
(440) 946-0076
http://www.lakesidecertifiedauto.com